Learn how to get extreme steering angle for your drift car! Not only will you learn how to install an angle kit, but you will learn how to replace the entire front suspension including the lower control arm, wheel bearing, tie rods, coilovers, sway bar, steering knuckle, and brakes.
Tools and Products
Bump Steer Kit: http://amzn.to/2DvleBE
Angle Kit: https://goo.gl/5ZiZQK
Extendable Ratchet: http://amzn.to/2DzNH9x
Wrench Set: http://amzn.to/2Dty2cA
Torque Wrench (goes to 250ft-lbs):http://amzn.to/2DV6WrY
Thread locker: http://amzn.to/2BfMCi2
Antiseize: http://amzn.to/2roe8Kz
Electric Cutoff Wheel: http://amzn.to/2DlXvk8
Wheel Bearing: http://amzn.to/2DztiRM
Stiffer Springs: http://amzn.to/2Dm936Q
Thanks Chris Forsberg for footage of his car: https://www.youtube.com/user/chrisforsbergracing
→ Become a ChrisFix Subscriber: http://www.youtube.com/subscription_center?add_user=paintballoo7
→ Instagram: https://www.instagram.com/chrisfixit
→ Facebook: https://www.facebook.com/chrisfix8
→ Website: http://www.ChrisFixed.com
→ My Channel Home Page: https://www.youtube.com/ChrisFix
**If the video was helpful, remember to give it a “thumbs up” and consider subscribing. New videos every Week**
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
Here is an UPDATE: https://www.youtube.com/user/PaintballOO7/community
New video coming out soon!!!
What happens to the Sway bar mount bolts on the frame. I still see them there hanging…
So what you’re saying is 2 and a half inches is a lot
Yep bad engineering
I’ve hadn’t watched Chris fix in 5 years and he was 1 mil and he is 10 FRICKIN MIL
Where would I find the torque specs for the bolts on these parts?
Please face reveal I will sub
love your videos men but the best part is when you say soapy wooder!!!!!!😅🤣🤣🤣
1:23 you can tell Chris only cared about cars in school and didn’t pay attention in class
"Ok we have to remove everything, so let's start with the brakes… but actually we have to start with the wheel spacer."
I love Chris’s car because it he installed an exhaust and he also installed a Hydro break also installed performance carbon fire clutches and she’s the best YouTuber ever the best YouTuber ever he makes199 million horsepower and his car is just the best of car ever I did another mustang because that mustang is too good for him. If I just got a Mustang like that I can’t really get a Mustang like that. Must like that. I can’t really get that. I don’t even know where it is, so I would tell Chrisfix and you know it’s just the best YouTuber and he’s just the best YouTuber. I watch all of his videos about the angle kit the first time drifting and he just think it good at drifting so he stalled a Hydro break cause I had your break and he’s like you know he like the best YouTuber ever if you watch his videos subscribe and get a big thumbs up to him I always do that when I watch his videos and Chrisfix you’re just the best YouTuber ever I just wanna say you’re the best YouTuber I’ll come visit you in New Jersey when I turn 16.
with experience, having an angle kit is 100% worth it. full lock and just a little gas and it will spin even a 120 horsepower beater. in my new edge it spins if i even press the gas at full lock.
When you drift the driftstang is go muuuussssstttsssaaaaaaaaaáaaaaaannnnnnnng
Suiiii
without a front sway bar what prevents the front end from waying pack and forth like a boat in a storm?
It did not come out because what if you were driving and the bolt fly out
Hi
Chis Fix you should get a RX7 and make it a drif car
how does this guy remove bolts so easy, i literally have a stuck oil drain plug rn and nothing is working
Will Chris reply to this 5 year old video? I'm not sure, but I will ask anyway.
When you removed the sway bar, was there a difference in comfort? I'm thinking about doing this to my Honda Civic EK3.
Can you upload a video on how to install a turbo charger? There are other tutorials from other channels, but I don't feel like doing it without watching a Chrisfix video.
Thanks for the great content man!
Do you do all the cussing off screen? 😂😅
hi guys chrisfix here and today i'm going to show you how to build a whole car with common hand tools!
I. Am soo impressed by chrisfix
For anyone watching this, first off love these tutorials. Awesome for us beginners but; Please do yourselves a favour and get a ball joint removal tool. I got mine for $50 CAD and it will save you so much pain if you have persistent ball joints. No real chance of damage and they pop off in less than a minute with no hammering.
They sell this kit for $1000. You can either do this yourself for almost no money, or have a local welder do it for you for less than $200
I like when cars have a lower steering ratio bc when I turn like to have a little swing to it.
What is the mustang name
How much horsepower it got? Im trying to make the same car in a game
I love you chris
Those control arm bolts are classic Ford engineering 😂😂
medium-strength threadlocker.
How to: Lightning mcqueen in cars 1
He has no medical conditions. But he has a lover medium strength thread-Locker. This is Chris