How to Replace a Window Regulator Motor (DIY) – Everything Law and Order Blog

Window wont roll up? Learn how to replace a window regulator motor in your car. Replacing the window motor is less expensive than replacing the entire window regulator assembly. Replacing the window motor can fix a window that is stuck down, or doesn’t roll down at all. Also if your window is getting stuck or is slow to go up and down, or it is making a grinding or whining noise, this video will show you how to repair it.

Extendable Ratchet Set: https://amzn.to/3h8gw2q
Window regulator motors: https://ebay.us/UnyoLL
Dry lubricant for windows: https://ebay.us/oiFwo8
Butyl Tape: https://ebay.us/mXW2CX
Medium strength threadlocker: https://ebay.us/oNtH5z
Silicone Paste (dielectric grease): https://ebay.us/9AFFDW
Common hand tools: https://tengtoolsusa.com/

0:00 Intro of how to replace a window regulator
1:28 How to diagnose a bad window motor
6:58 Tools and products
7:32 How to remove the door panel
9:27 How to remove old window motor
12:27 How to install new window motor
15:52 How to install door panel
17:32 Testing window regulator and motor

→ As an Amazon Associate I earn from qualifying purchases.
→ Become a ChrisFix Subscriber: http://www.youtube.com/subscription_center?add_user=paintballoo7
→ Instagram: https://www.instagram.com/chrisfixit
→ Facebook: https://www.facebook.com/chrisfix8
→ Website: http://www.ChrisFixed.com
→ My Channel Home Page: https://www.youtube.com/ChrisFix

**If the video was helpful, remember to give it a “thumbs up” and consider subscribing.**

Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

source

By phillyfinest369

ANGELHOUSE © 2009 - 2024 | HOSTING BY PHILLYFINEST369 SERVER STATS| & THE IDIOTS ROBOT AND CONTROL INC. |(RSS FEED MODULE)| ALL YOUTUBE VIDEOS IS A REGISTERED TRADEMARK OF GOOGLE INC. THE YOUTUBE CHANNELS AND BLOG FEEDS IS MANAGED BY THERE RIGHTFUL OWNERS (phillyfinest369.com)

41 thoughts on “How to Replace a Window Regulator Motor (DIY)”
  1. For everyone wondering, the Lemon BMW videos are coming up shortly but we had a mishap at the race which messed up all my planned videos haha. But stay tuned because once the car is back, I have some epic videos to share with you guys!

  2. For me my rear right window first wouldn’t go up but it went down just fine. Then the same thing happened to the rear window then the front passenger window was starting to act up. I took it to Firestone and they said it was a dealership only thing. I took it there and it was gonna be 1,110 to fix it. I’m like nah and I’m gonna try and find the parts needed

  3. 2:28 one of the car repairs I made when I was maybe 14 was when the cig lighter ports on a 2013 Honda odyssey was not working so I was at my grandparents’s house and I was able to get the fuse for the port and it was blowned so I went to autozone with my grandfather to buy some new fuses so I was able to install it into the car

  4. Is your hummer a 6.5 Diesel??
    I have one in my 1999 Suburban. I get 19 mpg on HWY w/ AC on & full of vacation stuff ! The PMD was a headache untill I did the relocation thing AND mounted a second unit for backup!!

  5. Thanks! Just did regulator for my 05 lesabre. I would advise to clean the glass before operating the window. The steel cables freyed and some of those tuny metal bits scratched the glass when the new one was in.

  6. Man i needed this 3 years ago when I bought my last beater, 99 jetta, for me it turn out to be the regulator. But i replaced the motor and regulator. Not a bad fix but its still a great car, and junkyard parts keep it cheap and cheerful.

  7. I bought a Dorman unit. It came in a box to fit with absolutely NO packing material! There was a big hole in the box right where the motor was located, and a big hole in one of the corners. The motor tested dead. I returned it. After multiple attempts to get a refund, they gave me only a little over 50% back. I will never buy from them again!

  8. Electrician here. Really good part on the electrics side, however you could have also mentioned that if you really need to replace a fuse and don't have the fitting one, you could also always use a smaller size one and hope that it doesn't blow. The fuses are there to protect the components and the cable tree, and nothing else. So, if it pops at a smaller current, it really doesn't damage your car. Also it would've been cool of you to show replacement of the moisture barrier using parts that you can get at a regular hardware store. Other than that, I love your videos. Keep it up.

Leave a Reply